Parts
Please excuse the quality of some pictures as they were gathered from websites
and standardized to fit this page.
Building a complete upper? You will need the following: Barrel, Receiver,
Charging Handle, Bolt Carrier Group, Handguard System, Gas Tube and Gas Block.
Muzzle devices are optional, but usually desired. Add $25 to the barrel for
muzzle threading and add $25 to assemble a complete upper with your specified
barrel and parts.
These are just a few parts that I commonly use. I can build with any parts you
specify.
Receivers
| LowPro |
$100 |
 |
| DPMS Low Profile Flattop without dustcover, forward assist or
brass deflector. This is the receiver used on my basic uppers. Only
available with standard feed ramps. |
| CMT A4 |
$125 |
 |
| Typical flattop receiver with dustcover, forward assist and
brass deflector. Laser engraved "T" numbers. Standard or M4 feed ramps. |
| A2 |
$160 |
 |
| Typical A2 type receiver with rear sight, dustcover, forward
assist and brass deflector. Only available with standard feed ramps. |
Bolt and Charging Handle Assemblies
| Charging Handle |
$25 |
 |
| LMT complete AR-15 charging handle. |
| Gas Buster |
$90 |
 |
| PRI M84 gas buster AR-15 charging handle with big latch. |
| Gas Buster |
$90 |
 |
| PRI M84L gas buster AR-10 charging handle with big latch. |
| Extended charging handle latch |
$20 |
 |
| Badger "First Generation" extended latch. |
| Extended charging handle latch |
$20 |
 |
| Badger "Second Generation" extended latch. |
| 5.56 Bolt Carrier Group |
$125 |
 |
| Complete bolt carrier group for 223/5.56 case head sized cartridges. |
| LMT "Enhanced" 5.56 Bolt Carrier Group |
$285 |
|
| Dual Extractor Spring bolt carrier group for 223/5.56 cases. |
| 6.8 SPC Bolt Carrier Group |
$150 |
|
| Complete bolt carrier group for use in 6.8 SPC uppers. |
| 6.5 or 7.62x39 Bolt Carrier Group |
$150 |
|
| Complete bolt carrier group for use in 6.5 Grendel or 7.62x39 uppers. |
| YM M16 Bolt Carrier |
$130 |
 |
| Young Machine chrome M16 bolt carrier with gas key. |
| YM M16 Bolt Carrier Group |
$195 |
|
| Young Machine chrome bolt carrier group with CMT bolt. |
| 5.56 Bolt |
$50 |
 |
| Complete bolt for 223/5.56 case head sized cartridges. |
| LMT "Enhanced" 5.56 Bolt |
$155 |
 |
| Dual Extractor Spring bolt for 223/5.56 case head sized cartridges. |
| 6.8 Bolt |
$75 |
|
| Complete bolt for use with 6.8 SPC barrels. |
| 6.5 & 7.62x39 Bolt |
$75 |
|
| Complete bolt for use with 6.5 Grendel or 7.62x39 barrels. |
Handguards
| Carbine Tube |
$50 |
 |
| Basic DPMS carbine length aluminum free float handguard tube. |
| Rifle Tube |
$55 |
 |
| Basic DPMS rifle length aluminum free float handguard tube. |
| Vented Carbine Tube |
$75 |
 |
| DPMS vented carbine length aluminum free float handguard tube. |
| Vented Rifle Tube |
$80 |
 |
| DPMS vented rifle length aluminum free float handguard tube. |
| Carbon Fiber Carbine Tube |
$90 |
 |
| DPMS carbine length carbon fiber free float handguard tube. |
| Carbon Fiber Rifle Tube |
$100 |
 |
| DPMS rifle length carbon fiber free float handguard tube. |
| Briley Rifle Tube |
$110 |
 |
| Briley rifle length carbon fiber free float handguard tube. |
| YHM 7.2 Customizable |
$85 |
 |
Yankee Hill carbine length customizable handguard.
Various rails
are available below. |
| YHM 12.5 Customizable |
$115 |
 |
Yankee Hill rifle length customizable handguard.
Various rails
are available below. |
| Rails for Yankee Hill customizable handguards: |
 |
| 3" Rail |
$20 |
| 4" Rail |
$22 |
| 7" Rail |
$25 |
| 9" Rail |
$30 |
| 12" Rail |
$40 |
| YHM 7.2 Lightweight |
$120 |
 |
| Yankee Hill carbine length lightweight quad railed handguard. |
| YHM 9.2 Lightweight |
$130 |
 |
| Yankee Hill mid-length lightweight quad railed handguard. |
| YHM 12.5 Lightweight |
$160 |
 |
| Yankee Hill rifle length lightweight quad railed handguard. |
| YHM Wrench |
$30 |
 |
| Wrench for installing YHM handguard systems. |
| Daniel Defense 7.0 |
$275 |
 |
| Daniel Defense carbine length quad railed handguard. 8.5 oz. |
| Daniel Defense 7.0 Lite Rail |
$325 |
 |
| New style carbine length quad railed handguard. 8.5 oz. |
| Daniel Defense 9.0 |
$310 |
 |
| Daniel Defense mid-length quad railed handguard. 11.0oz. |
| Daniel Defense 9.0 Lite Rail |
$375 |
 |
| New style mid-length quad railed handguard. 11 oz. |
| Daniel Defense 9.0 AR-10 Lite Rail |
$375 |
 |
| Mid length quad railed handguard for the AR-10. 13.5 oz. |
| Daniel Defense 9.5 FSP |
$320 |
 |
| Mid-length rails for use with a carbine located FSB. 10.2oz |
| Daniel Defense 9.5 FSP Lite Rail |
$385 |
 |
| New style mid-length rails for use with a carbine FSB. 10.2oz |
| Daniel Defense 12.0 |
$340 |
 |
| Daniel Defense rifle length quad railed handguard. 13oz. |
| Daniel Defense 12.0 Lite Rail |
$425 |
 |
| New style rifle length quad railed handguard. 14oz. |
| Daniel Defense 12.0 AR-10 Lite Rail |
$425 |
|
| Rifle length quad railed handguard for the AR-10. 18.5 oz. |
| Daniel Defense 12.0 FSP |
$360 |
 |
| Rifle length rails for use with a carbine located FSB.
12.5oz. |
|
Daniel Defense 12.0 FSP Lite |
$440 |
 |
| New style rifle length rails for use with a carbine located FSB.
13.7oz. |
| Daniel Defense 12.0 FSPM |
$360 |
 |
| Rifle length rails for use with a mid-length located FSB.
12.3oz. |
| Daniel Defense 12.0 FSPM Lite |
$440 |
 |
| New style rifle length rails for use with a mid-length FSB.
13.6oz. |
| Daniel Defense 14.0 AR-10 Lite Rail |
$Call |
|
| Extended length quad railed handguard for the AR-10. 20.5 oz. |
| LaRue 7.0 |
$250 |
 |
| LaRue carbine length quad railed handguard. 11.2oz. |
| LaRue 9.0 |
$275 |
 |
| LaRue mid-length quad railed handguard. 12.8oz. |
| LaRue 12.0 |
$300 |
 |
| LaRue rifle length quad railed handguard. 16oz. |
| LaRue 13.2 |
$330 |
 |
| LaRue extended length quad railed handguard. 17.6oz. |
| LaRue 13.2 AR-10 |
$330 |
 |
| LaRue AR-10 extended length quad railed handguard. 19oz. |
| PRI 7.0 |
$315 |
 |
| PRI carbine length Gen III handguard, natural finish. Black
finish is also available and shown on the rifle length version below. |
| PRI 9.0 |
$315 |
 |
| PRI mid-length Gen III handguard, natural finish. Black finish
is also available and shown on the rifle length version below. |
| PRI 12.0 |
$320 |
 |
| PRI rifle length Gen III handguard, black finish. Natural finish
is also available and shown on the 2 versions above. |
| JP 12.0 |
$150 |
 |
| JP Enterprises has a variety of handguards available, this is
the black rifle version, but I can get any of them. |
| JP 7.0 |
$150 |
 |
| JP Enterprises has a variety of handguards available, this is
the black carbine version, but I can get any of them. |
| Badger Ordinance 7.0 |
$150 |
 |
| Badger's flat bottomed "stabilizer" handguard in carbine length. |
| Badger Ordinance 12.0 |
$160 |
 |
| Badger's flat bottomed "stabilizer" handguard in rifle length. |
Gas System
| Gas Tube |
$15 |
 |
| Specify Pistol, Carbine, Mid-Length, Rifle length or Extended
length. |
| Shaved Gas Block |
$40 |
 |
| Simple 0.750" aluminum gas block. Fits under
most handguards. |
| Bull Barrel Gas Block |
$40 |
 |
| Simple 0.940" aluminum gas block. Fits under most
handguards. 1.6oz |
| MI Low Profile Gas Block |
$45 |
 |
| Simple 0.750" steel gas block. Fits under most
handguards. 3.5oz |
| Railed Gas Block |
$40 |
 |
| DPMS 0.750" aluminum gas block with a picatinny rail on top.
2.5oz |
| Bull Barrel Railed Gas Block |
$40 |
 |
| DPMS 0.940" aluminum gas block with a picatinny rail on top. |
| Quad Railed Gas Block |
$50 |
 |
| DPMS 0.750" aluminum gas block with a 4 picatinny rails.
3.4oz |
| Steel Railed Gas Block |
$40 |
 |
| Stag 0.750" steel gas block with a picatinny rail. 5.1oz |
| AR-10T Stainless Steel Railed Gas Block |
$50 |
 |
| Armalite 0.875" stainless steel gas block with a picatinny rail.
4.4oz |
| JP 0.750" Adjustable |
$70 |
 |
| JP Enterprises original adjustable gas block in anodized
aluminum. 1.9oz |
| JP 0.750" Low Profile Adjustable |
$70 |
 |
| JP's new 0.750" new low profile steel adjustable gas block. |
| JP 0.940" Adjustable |
$80 |
 |
| JP Enterprises adjustable gas block for bull barrels,
aluminum. 2.5oz |
| JP 0.940" Shaved Adjustable |
$90 |
 |
| I take a 0.940" JP aluminum block and turn it down to fit under
a handguard tube. You need this on any barrel where the gas port/block is
covered by the handguard tube such as 300x221 or dissipater setups. |
| LaRue Low Profile |
$70 |
 |
| Steel 0.625" low profile gas block made by LaRue Tactical.
3.9oz |
| LaRue Low Profile |
$70 |
 |
| Steel 0.750" low profile gas block made by LaRue Tactical.
2.8oz |
| LaRue Low Profile |
$70 |
 |
| Steel 0.875" low profile gas block made by LaRue Tactical.
2.8oz |
| LaRue Low Profile |
$90 |
 |
| Steel 0.940" low profile gas block that I modify to fit bull barrels.
2.1oz |
| AR15barrels Low Profile |
$55 |
 |
| Steel 0.625" lightweight low profile adjustable gas block.
1.3oz |
| PRI Low Profile |
$55 |
 |
| Steel 0.750" low profile gas block made by PRI. 1.4oz |
| YHM Low Profile |
$40 |
 |
| Steel 0.750" low profile gas block made by YHM. 4.4oz |
| YHM Specter |
$40 |
 |
| Steel 0.625" low profile clamp-on gas block made by YHM
allows profiles to be larger than 0.625" in front of the gas block. 5.5oz |
| YHM Specter |
$40 |
|
| Steel 0.750" low profile clamp-on gas block made by YHM
allows profiles to be larger than 0.750" in front of the gas block. 4.4oz |
| YHM Dual Rail |
$65 |
 |
| Steel 0.750" dual rail gas block by YHM
allows profiles to be larger than 0.750" in front of the gas block. 7.2oz |
| YHM Flip-Up Front Sight, clamp-on |
$90 |
 |
| Flip-up front sight that clamps on to the barrel. Allows barrel
profiles with larger steps up front. 6.0oz |
PRI Flip-Up Front Sight, clamp-on, 0.625" or 0.750"
0.750" model is 4.6 oz. |
$180 |
 |
| Flip-up front sight that clamps on to the barrel.
Picture Picture |
Flash Hiders, Brakes & Comps
| A2 |
$10 |
 |
| Your plain jane military A2 flash hider / comp, 1/2"-28 threads. Requires indexing. |
| A1 |
$10 |
 |
| Military A1 "Birdcage" flash hider, 1/2"-28 threads. No indexing
required. |
| Three Prong |
$10 |
 |
| Old School military flash hider, 1/2"-28 threads. No indexing
required. |
| Stag Comp |
$15 |
 |
| Stag Arms basic 3 port comp, 1/2"-28 threads. Requires
indexing. |
| Phantom |
$30 |
 |
| YHM standard 4 port phantom flash hider, 1/2"-28 threads.
No indexing required. |
| Phantom 5C1 |
$30 |
 |
| YHM phantom flash hider with a closed bottom port, 1/2"-28
threads. Requires indexing. |
| Phantom 5C2 |
$30 |
 |
| YHM phantom flash hider with a closed bottom port, 1/2"-28
threads. Requires indexing. |
| 308 Phantom |
$35 |
 |
| YHM phantom flash hider for 6.8 SPC and 308, 5/8"-24
threads. No indexing required. |
| 308 Phantom 5C1 |
$35 |
 |
| YHM phantom flash hider with a closed bottom port for 6.8 SPC and 308, 5/8"-24
threads. Requires indexing. |
| 308 Phantom 5C2 |
$35 |
 |
| YHM phantom flash hider with a closed bottom port for 6.8 SPC and 308, 5/8"-24
threads. Requires indexing. |
| Vortex |
$50 |
 |
| Smith Enterprises 5.56 Vortex G6 flash hider, 1/2"-28 threads.
No indexing required |
| Vortex |
$60 |
|
| Specially made Smith Enterprises Vortex G5 30 caliber flash hider, 9/16"-24 threads for 6.8 SPC and 30 caliber barrels. Same diameter at the 5.56 version (0.860"), but there is no skirt on rear. No indexing required |
| 308 Vortex |
$85 |
 |
| Smith Enterprises 6.8 SPC and 308 Vortex G6 flash hider, 5/8"-24 threads.
No indexing required |
| Miculek Comp |
$50 |
 |
| DPMS manufactured 1/2"-28 threads. Requires indexing. |
| 308 Miculek Comp |
$65 |
 |
| DPMS manufactured for 6.8 SPC and 308 with 5/8"-24 threads. Requires indexing. |
| MSTN QC Comp |
$80 |
 |
| Stainless steel with 5/8"-24 threads. Requires
indexing. |
| Black MSTN QC Comp |
$82 |
 |
| Blackened stainless with 5/8"-24 threads. Requires
indexing. |
| Bennie Cooley Comp |
$90 |
 |
| JP Enterprises stainless steel with 1/2"-28 threads. Requires
indexing. |
| Big Bennie Cooley Comp |
$90 |
|
| JP Enterprises stainless steel with 5/8"-24 threads. Requires
indexing. |
| Fat Bennie Cooley Comp |
$90 |
|
| JP Enterprises stainless steel with 5/8"-28 threads. Sized
to work on a bull barrel. Requires
indexing. |
| JP Recoil Eliminator |
$115 |
 |
| JP Enterprises stainless steel with 3/4"-28 threads. Sized
to work on a bull barrel. Requires
indexing. |
| OPS INC Brake |
$115 |
 |
| OPS INC stainless steel brake. Available with 1/2"-28, 9/16"-24
or 5/8"-24 threads. Requires
indexing. |
|
